Introducción a la funciónDespués de la instalación de este sistema, cuando se enciende el vehículo, los sensores de microondas en ambos lados de la parte trasera enviarán una señal de sonido de microondas hacia atrás. Cuando se detecta que se acerca un vehículo en el área ciega, el sistema procesará la señal reflejada. Cuando confirma que hay un objeto acercándose, alerta al conductor emitiendo las señales sonoras y luminosas correspondientes. 1.Cuando el vehículo se acerca, el lado correspondiente de las luces LED se iluminará para indicar que la parte trasera del vehículo se acerca. 2.Cuando el LED está encendido, si el conductor enciende la señal de giro correspondiente, el LED parpadeará y el timbre sonará para indicar que el cambio es arriesgado en este momento. 3. Una vez que se detiene el vehículo, el sistema se demora 30 segundos. Cuando hay bicicletas, coches eléctricos, motocicletas, peatones y otros vehículos cerca del vehículo, el sistema se enciende y existe el riesgo de que se abran las puertas. Confirme la seguridad antes de abrir las puertas.las características y escenarios de la aplicación1. El tiempo lluvioso, los parabrisas y los espejos están cubiertos de gotas de agua, visión borrosa, cambiar el camino es muy peligroso.2. Tiempo de niebla, poca visibilidad del tráfico, línea de visión más corta, espejo retrovisor borroso, cambiar de carril es peligroso.3 clima nevado, vidrios, espejos de hielo, ojos alterados, visión borrosa, cambiar el camino es muy peligroso.4. Falta de atención, charlar con otras personas, cambio a ciegas, muy peligroso.Advertencia La línea amarilla está conectada con la batería común, batería B + línea roja luego ACC + Conexión a tierra de la línea negra -Las luces de giro se conectan al positivo de la lámpara correspondiente Otro cable de extensión marcado directamente según la marcaRequerimientos de instalación La superficie de transmisión de señal del sensor solo puede penetrar la carcasa del parachoques de plástico y no puede penetrar el metal. El sensor puede verse afectado por la luz fluorescente El sensor debe fijarse firmemente con un soporte o pegamento 3M sin agitar. Los terminales del sensor están verticalmente hacia abajo y paralelos hacia afuera 25 Instrucciones de uso: Cuando detecta un vehículo en movimiento o personas cercanas, la luz de advertencia LED correspondiente parpadeará en alarma. Cuando la luz de alarma está encendida, si el conductor enciende la luz de giro correspondiente, la luz de alarma LED parpadea y el timbre suena como alarma.Lista de productos1.BSD host 1 PC2.Sensor 2 piezas3.Luz de advertencia LED 2 piezas4.Opcional: Espejo retrovisor especial 2 PC5.Zumbador externo 1 PC6.Arnés principal 1 piezas7.Arnés de cableado BSD 1 PC8.Cable de extensión 4 piezas9.Soporte fijo 1 piezasCinta de 10,3 M 4 piezas11.Manual 1 piezas12.Pies en ángulo 1 piezasParámetros del sistemaFrecuencia del sensor 24GHZPrecisión de detección de 0,25 CMAlcance máximo de detección de peatones: 0.3M-10MMotocicleta: 0.3M-10MCamión: 0.3M-20MRango de medición de alarma de 0,3 a 20 metros.Coche con sistema eficiente> 98%Peatón> 95%Modo de alarma 1: el LED está siempre encendido2: LED parpadea + zumbadorGrado de impermeabilidad IP67Corriente de funcionamiento 200MAVoltaje de funcionamiento 9V-16VTemperatura de funcionamiento -30 grados Celsius + 80 grados CelsiusTemperatura de almacenamiento -40 grados Celsius + 85 grados CelsiusÁngulo de detección Horizontal 54 grados X Vertical 28 gradosAdvertencia: Antes de cambiar de carril, asegúrese de confirmar el entorno circundante. En algunos casos, el sistema puede fallar, como: pendientes pronunciadas, vértices de carreteras de montaña, curvas cerradas, etc.---------Function IntroductionAfter installation of this system, when the vehicle is started, the microwave sensors on both sides of the rear will send a microwave sounding signal backwards. When a vehicle in the blind area is detected to be approaching, the system will processes the reflected signal. When it confirms that there is an object approaching, it alerts driver by issuing the corresponding sound and light signals. 1.When the vehicle is approaching, the corresponding side of the LED lights will be lit to prompt the rear of the vehicle near. 2.When the LED is lit, if the driver turns on the corresponding turn signal, the LED will flash and the buzzer will sound to indicate that the turnaround is risky at this time. 3.After the vehicle is stopped, the system delays for 30s. When there are bicycles, electric cars, motorcycles, pedestrians and other vehicles near the vehicle, the system will light up and there is a risk of opening the doors. Please confirm the safety before opening the doors.the application features and scenarios1. Rainy weather, windshields and mirrors are covered with water droplets, blurred vision, change the road is very dangerous.2. Foggy weather, traffic visibility is low, line of sight shorter, rear blur mirror, changing lanes is dangerous.3 snowy weather, glass, mirror ice, eyes were disturbed, blurred vision, change the road is very dangerous.4. Inattention, chatting with other people, blind change, very dangerous.Warning Yellow line is connected with common battery, battery B + red line then ACC + Black line grounding -Turn lights connect to the positive of the corresponding lamp Other extension wire directly marked according to the markInstallation requirements The signal transmitting surface of the sensor can only penetrate the plastic bumper shell and can not penetrate the metal. The sensor may be affected by fluorescent light The sensor should be firmly fixed with a bracket or 3M glue without shaking. The sensor terminals are vertically downward and parallel outward 25 Instructions for use: When it detects moving vehicle or people near, the corresponding LED warning light will flash to alarm. When the alarm light is on, if the driver turns on the corresponding turn light, the LED alarm light flashes, and the buzzer sounds alarm.Products list1.BSD host 1 PCs2.Sensor 2 PCs3.LED warning light 2 PCs4.Optional: Special rear mirror 2 PCs5.External buzzer 1 PCs6.Main harness 1 PCs7.BSD wiring harness 1 PCs8.Extension cord 4 PCs9.Fixed bracket 1 PCs10.3M tape 4 PCs11.Manual 1 PCs12.Angle feet 1 PCsSystem parametersSensor frequency 24GHZDetection accuracy of 0.25CMMaximum detection range of pedestrians: 0.3M-10MMotorcycle: 0.3M-10MTruck: 0.3M-20MAlarm measuring range of 0.3-20 metersSystem efficient car> 98%Pedestrian> 95%Alarm mode 1: LED is always on2: LED flashes + buzzerWaterproof rating IP67Operating current 200MAOperating voltage 9V-16VOperating temperature -30 Degrees Celsius +80 Degrees CelsiusStorage temperature -40 Degrees Celsius +85 Degrees CelsiusDetection angle Horizontal 54 Degrees X Vertical 28 DegreesWarning: Before changing the lane, be sure to confirm the surrounding environment. In some cases, the system may fail, such as: steep slopes, mountain road vertices, sharp bends and so on.